How to Do Physical Verification of Fixed Assets, Step by Step
Simple Asset Tracker Team · · 7 min read
Physical verification of fixed assets means going out, finding each asset on your register and confirming it exists, sits where the register says and is in usable condition. The method has three stages: plan the count (which includes cleaning the register and checking every asset has a readable tag), count from the register to the floor and from the floor to the register, then resolve the discrepancies and write it up. Here's how we'd run each one, with a checklist at the end.
What physical verification of fixed assets has to prove
Your fixed asset register lists what the company owns: laptops, servers, furniture, machines, vehicles. A verification checks that list against what's physically there. It answers three questions for every line: is the asset there, is it where the register says, and is it in a state anyone would still call usable?
It also has to work the other way round. An asset sitting on a desk that isn't on the register is a finding too. It can mean a purchase was expensed that should have been capitalised, or an asset was transferred in and nobody recorded it. It may also turn out to be below your capitalisation threshold, leased, or someone else's property.
For companies that CARO 2020 applies to, the statutory auditor reports on whether management has physically verified property, plant and equipment at reasonable intervals, whether any material discrepancies were noticed, and whether they were properly dealt with in the books of account (paragraph 3(i)(b)). CARO doesn't fix a frequency. ICAI's Guidance Note on CARO 2020 says annual verification may be reasonable and, where that isn't practicable, the programme should still cover every asset at least once in three years. So some companies count everything every year and others phase it. Whichever you choose, write it down, because the first thing anyone reviewing the count will ask is what the plan was. (If you'd rather run the count on phones, here's how verification works in Simple Asset Tracker.)
Planning the count
When a verification drags on for weeks, the cause is usually something that could have been settled beforehand. Settle these before anyone picks up a phone or a clipboard.
Fix the scope and the cut-off date
Decide which locations, asset classes and entities are in this round, and pick a cut-off date. The register you verify against should be the register as at that date. If purchases and transfers keep flowing into it while people are counting, you'll spend days chasing differences that are just timing.
Clean the register first
Export the register and look for the obvious problems: duplicate rows, assets with no location, descriptions like "Laptop" with no serial number, and groups booked as one line ("10 chairs") that the counter will need to see as ten. It's an afternoon's work now; leave it until the count and you'll have people standing in a corridor trying to work out which "Dell laptop" they're looking at. Each asset also needs a tag the counter can read and match to one line of the register. If tags are missing or worn, re-tag before the count, not during it. We compared the options in QR code asset tags vs handwritten labels.
Assign people to locations
Split the register by location and give each team a manageable area, say one floor or one warehouse bay per person per day. Where you can, have assets counted by someone other than the person who looks after them day to day. A custodian confirming their own assets isn't much of a check.
Tell people it's happening
Send a short note a week ahead: when the count is, what verifiers will need (access to locked rooms, cabinets, server racks), and a request not to move assets between sites during the count. Laptops are the hard part. If staff take theirs home or travel, either schedule a day when everyone brings them in, or collect serial numbers through IT and verify them separately.
Counting in both directions
A good count runs two ways.
Book to floor means starting from the register: for each line, find the asset, read its tag and record the result. This is how you find assets that are missing.
Floor to book goes the other way. Start from the room, walk it and look at everything that should be on a register: every desk, monitor, cabinet and machine. Anything without a tag, or with a tag that doesn't match the register, gets written down with a description, serial number and location. This is how you find assets that were never recorded.
For every asset, the result should be one of a small set of values, recorded the same way by every verifier:
- Verified: found where the register says.
- Misplaced: found, but somewhere else. Record where.
- Missing: not found after a proper search.
Alongside the result, note anything that matters for the accounts: damage, assets that look idle or obsolete, and assets in use by a different department. Those notes go to finance after the count, because an idle or damaged asset raises questions about its value even if it was found exactly where it should be.
Don't mark something missing too early. Projectors, ladders and testing equipment move around. A quick message to the custodian before closing the location saves a long investigation later.
Dealing with what the count turns up
Once the counting stops, pull the results together and sort the exceptions into groups:
- Misplaced assets. Either move them back or update the location in the register. Get the custodian to confirm which.
- Missing assets. Investigate each one: was it disposed of without the register being updated, transferred to another entity, sent for repair, lost or stolen? Keep a note of what was found and who confirmed it.
- Assets found but not on the register. Trace each one to a purchase invoice or transfer document so finance can decide how it should be recorded.
- Damaged or idle assets. Pass the list to finance for their review of carrying values.
Adjustments to the books, such as writing off an asset that can't be found, are decisions for finance and management, and they should be approved and documented. The verification team's job is to put the evidence in front of them.
Finally, write a short report: scope, cut-off date, who counted what, the number of assets verified, misplaced, missing and unrecorded, how each discrepancy was dealt with, and sign-offs. Keep the detailed sheets with it. If anyone asks next year how an asset was verified, this is what you'll show them.
A checklist you can reuse
- Verification plan approved: scope, locations, asset classes, frequency or cycle.
- Cut-off date fixed and the register frozen as at that date.
- Register cleaned: duplicates removed, locations filled, grouped lines split.
- Every asset tagged and every tag readable.
- Verifiers assigned by location, independent of custodians where possible.
- Staff told the dates; access to locked areas arranged; laptops planned for.
- Book-to-floor count done for every line in scope.
- Floor-to-book walk done in every location.
- Each asset recorded as verified, misplaced or missing, with notes on damage or idle use.
- Misplaced assets moved back or register updated.
- Missing assets investigated and outcomes recorded.
- Unrecorded assets traced to documents and passed to finance.
- Adjustments approved by the right people and recorded in the books.
- Report signed and filed with the working sheets.
Running the count without the paperwork
All of this works on paper, and plenty of companies still do it that way. It's slow, though. We went through where the paper process breaks in paper vs digital physical verification.
In Simple Asset Tracker the plan becomes a verification event with a name and a scheduled date. Admins assign assets to verifiers on screen or by importing a spreadsheet. Each verifier sees their own list on their phone, scans the QR tag and records the asset as verified, missing or misplaced, with a note and, for a misplaced asset, where it was actually found. Where there's no signal, results are saved on the phone and sent when it reconnects, still stamped with the time the asset was checked, so a basement storeroom doesn't hold anyone up. Admins can see coverage build up as results arrive instead of waiting for sheets to come back.
Anything the floor-to-book walk turns up that isn't on the register can be recorded from the same phone: what it is, where it was found and any serial number. It's listed on the event, so you can trace it to a purchase invoice or transfer document and finance can decide how it should be recorded. When the count is done, the event can be closed and its results exported to Excel for the report, with anything found off the register on a sheet of its own.
If your next verification is a few months away, start with the planning steps above on one location. You'll find most of the problems before the count rather than during it. If you'd like to try it with a phone instead of a printout, download Simple Asset Tracker. It's free for up to 30 assets.
Try it on your own assets
Simple Asset Tracker runs on your own computer or server. Import your register, print QR asset tags and run a verification from any phone. It's free for up to 30 assets.